Products sold by Anderson Composites may not be legal for street use in all states. It is the buyer’s responsibility to comply with applicable state laws. The buyer understands that due to strict U.S. Federal and State safety crash guidelines, Anderson Composites is not responsible or liable for any damages or possible injuries incurred upon possible accidents due to driver error, incorrect installations, bad judgment, or act of nature/God, Allah, Jehovah, etc. All products are intended for off-highway uses only, and should be used for their intended purposes only. Anderson Composites does not take responsibility over buyer installation, modification, and unusual stress of the products. The buyer assumes all responsibilities for determining the suitability of the products. Anderson Composites is not responsible for any damages incurred either directly or indirectly on the vehicles or operators/passengers within the vehicles.
Anderson Composites Fitment Guarantee
The following situations are fully covered under the Anderson Composites Fitment Guarantee:
Hoods:
The hood does not clear a stock engine.
The gap between the hood and the fenders is more than 1/2″ wide on each side.
The hood levels are more than 1/4″ higher or lower than the fenders.
The latch is 1/16″ too long or too short than the stock latch, causing the hood not to latch.
Please note that Anderson Composites does not suggest reinstalling gas hood shocks/dampers/struts.
Anderson Composites does not guarantee fitment on the cars that have been involved in accidents and/or had body damages.
Anderson Composites strongly recommends the use of heat shields. Damages to the hood resulted from the absence of heat shields will not be covered under the warranty.
Trunks:
The gap between the trunk and the rear fenders is more than 1/2″ wide on each side.
Trunk levels are more than 1/4″ higher or lower than the rear fenders.
Please note that Anderson Composites does not suggest reinstalling gas trunk shocks/dampers/struts.
Anderson Composites does not guarantee fitment on the cars that have been involved in accidents and/or had body damages.
Lips:
The length of the lip is 3/8″ too long or too short than the stock bumper.
Anderson Composites Appearance Guarantee
The following situations are fully covered under the Anderson Composites Appearance Guarantee: (Note that all Anderson Composites carbon fiber and fiberglass products are handmade, and small imperfections are inevitable.)
The heavy cloudiness under the clear finish, which is only visible under the sun. Anderson Composites apologizes for not being able to QC every product under natural sun light.
The clear finish bubble is larger than 3/8″ in diameter.
Anderson Composites Clear Finish Guarantee
The following situations are fully covered under the Anderson Composites Clear Finish Guarantee:
The clear finish changes color more than a full shade within 6 months. Note: like car paint, slight fading and discoloration are natural. The warranty only covers more extreme cases.
Installation
All products require professional installation. The buyer understands that some products may require modifications for correct fitment. Minor adjustments may be necessary as part of the normal installation process. All carbon fiber products will not sustain heavy force or weight, for they could be cracked by such force or weight. Anderson Composites has made an effort to produce all its aftermarket products to fit the original factory vehicles as closely as possible. However, some occasional prepping may be necessary for an ideal fit. The buyer needs to perform these steps to his/her satisfaction before installation. If the buyer wants to paint the products, he or she must prefit the parts to the vehicle before painting to ensure a proper fit.
Hood Pins
All hoods require hood pins for safety reasons. Anderson Composites will not be liable for any damages to the product and the vehicle caused by not properly using hood pins.
Heat Shields
Anderson Composites strongly recommends the use of heat shields for all carbon fiber and fiberglass hoods. Heat shields help avoid pre-mature aging of the product.
Defective Products
All products require professional installation. Minor adjustments might be necessary. These are normal body work and installation steps. Therefore it is not considered to be defective. In addition, most carbon fiber products are hand-crafted, and no two products will be identical. Small imperfections such as wavy weaves, small bubbles, and clear finish blemishes are inevitable. Defective products may be exchanged for the same product only.
Contingencies
Anderson Composites shall not be liable for any failures to produce the product to the buyer when the cause of such failure is the result of the forces of nature, labor disputes, supplies or material shortage, acts of local, state, national, civil, or other authorities or public agencies; utility or communication failures, accidents, strikes, transportation problems, or any act or cause that does not normally occur in the ordinary course of the Anderson Composites business.
Anderson Composites® - Hood Installation