CURT® - Class 3 Trailer Hitch with 2" Receiver Opening

The hitch looks great and fits well behind the cover on my wife's traverse. Very, very easy to install!

Good quality, easy to install and good looking, ah excellent customer service.

Received my Curt hitch super fast and couldn’t be more happier. It may not fit correctly immediately but once you play with it, it’s a great fit. Thanks to Curt, I’m able to put my bike rack. Not to mention how nice of this company for the free shipping! Get yours from them if you’re looking for one.

Great product. Easy installation with little experience. Sturdy and tough product.

Items arrived promptly and undamaged. Items were separately packaged thus making the previous possible. Solid construction and the easy to get it installed. For those not so mechanically inclined or don't have patience...Upon finding video via YouTube I promptly realized it would be easier to take it to the Creator of the installation video: U-Haul. For a mere $120.00 (pending location) they will install your hitch w/wiring harness in under an hour. And it's DONE CORRECTLY/PROFESSIONALLY! Between CARiD and UHaul, I can now safely tow my trailer! Thank you both!!!

I ordered this hitch for my 2021 Ford Bronco, 4 door. This is a high quality made hitch, I'm pleased with its construction, and the fit on the frame on the car. No complaints there. HOWEVER - the included bolts are 4 1/2" long, and they hit the rear bumper before being fully seated. They are too long, period. It is unsafe to install with these, as you will not be able to fully seat the bolt against the hitch. Additionally, the bolt interferes with the rear wiring harness. BOTH of these issues are brought up in the another customers review on this page from December as well. I have raised the issue to customer service - after much back and forth, I still do not think they understand the issue. BUT, they did credit me back $40 in gift cards, which I'm happy with as compensation. I personally believe you need 4" long, 1/2" diameter Grade 8 Zinc yellow coated bolts for this to work with this, and that is what I will be sourcing to mount this hitch. Overall - great hitch, wrong hardware included, but easy fix from any hardware supplier. Satisfied with customer service solution.

Hitch fits great but bolts are approximately half inch too long so they interfere with the bumper. I cut one but it took 3 blades (1 reciprocating saw and 2 manual hack saw) so I will be reaching out direct to Curt for new fastener set as I'm not spending the time to cut each bolt. Even with bolts shortened, it will interfere with the factory back up sensor harness so I will need to reroute or add cushion tape to prevent rub. Attached image shows bolt touching bumper surface with bolt head still 1-2mm from contact to hitch surface on the other side.

Received this in in good order. All things were as described and the installation instructions were not the best but adequate. There was 1 point where they stated you needed to back off a bumper fastener to get it to fit properly. I ignored this part until I realized that I had to back off this fastener about .25" in order for the hitch to fit properly. Another reviewer said she installed it by herself. Good for her, I needed another person to help lift it into position to set the carriage bolts. I could not do both by myself. There was some gaps on the dry fit but the carriage bolts were long enough to span that gap. While tightening it up, it pulled the hitch right to the frame. There are 2 bolts that need to be fished through the frame. However, they did not fit any holes in the frame that were existing. I needed to go to Home Depot to get a steel hole saw bit to open them up. That bit was $17. I want to say it is a 7/8" hole saw. Took about 30 seconds to open each hole and had no issue fishing the bolts through. Threw some paint on the bare metal and away I went. The hardest part for me was removing the exhaust from the 3 rubber mounts. I did not have the right tool to do this but made due with a pair of channel locks that worked out well.

This was just what I needed to add my Kuat rack to my new Subaru Outback. The price was as low as I could find, and it arrived much faster than I expected.

This Curt hitch is priced right and satisfies my need. I use it mainly to carry my two ebikes on a bike carrier. I also use it to carry a cargo hitch for travel. The square design is more slender than than the round ones. The foot sensor to open the back hitch still work.