Vehicle Fitment
Make | Model | Year |
---|---|---|
Volvo | C30 | 2008-2012 |
C70 | 2006-2010 | |
S40 | 2004-2007 | |
S60 | 2005-2007 | |
V50 | 2005-2007, 2010 | |
V70 | 2005 |
Make | Model | Year |
---|---|---|
Volvo | C30 | 2008-2012 |
C70 | 2006-2010 | |
S40 | 2004-2007 | |
S60 | 2005-2007 | |
V50 | 2005-2007, 2010 | |
V70 | 2005 |
Dual Mass Flywheel by LuK®. LuK dual mass flywheels absorb engine vibrations before they are transmitted to the driveline where they can create gear rattle. These units feature a built-in damper designed to isolate engine torque spikes and prevent transmission damage. By design, dual mass flywheels cannot be resurfaced.
Ring Gear Major Dia.: 12 inch |
Ring Gear Major Dia.: 304.8 mm |
Bolt hole PCD clutch pres.plte: 10.2362 inch |
Bolt hole PCD clutch pres.plte: 260 mm |
Flywheel Thickness [mm]: 2.4488 inch |
Flywheel Thickness [mm]: 62.2 mm |
Bolt Hole Pattern: 2 |
Overall Casting O.D.: 12.1024 inch |
Overall Casting O.D.: 307.4 mm |
I.D. for Pilot: 1.8504 inch |
I.D. for Pilot: 47 mm |
Crank To Friction Surface: 1.4724 inch |
Crank To Friction Surface: 37.4 mm |
Dowel Hole Pattern: 5 |
Ring Gear Thickness: 0.3543 inch |
Ring Gear Thickness: 9 mm |
Centering diameter / dowel hole: 10.2362 inch |
Centering diameter / dowel hole: 260 mm |
Ring Gear Number: L-09180-0025-03 |
Cup depth, secondary flywheel: -0.2992 inch |
Cup depth, secondary flywheel: -7.6 mm |
Flywheel friction surface outer diameter: 9.4094 inch |
Flywheel friction surface outer diameter: 239 mm |
Torque Capacity DMFW: 14.685 inch |
Torque Capacity DMFW: 373 mm |
Ring Gear Mounting O.D.: 11.0295 inch |
Ring Gear Mounting O.D.: 280.15 mm |
Number of teeth, starter ring gear: 144 |
Ring Gear To Friction Surface: 1.5551 inch |
Ring Gear To Friction Surface: 39.5 mm |
Flywheel Friction Surface Inner diameter: 5.9843 inch |
Flywheel Friction Surface Inner diameter: 152 mm |
Bolt hole PCD crankshaft: 3.189 inch |
Bolt hole PCD crankshaft: 81 mm |
Dowel hole diameter: 0.2362 inch |
Dowel hole diameter: 6 mm |
Crank Hole Dia.: 0.4626 inch |
Crank Hole Dia.: 11.75 mm |
The flywheel is an integral part of a clutch replacement. In today’s tightly packaged clutch systems, flywheels can easily be machined beyond their usable life – a critical flaw that would not be evident until after the clutch is installed. Improper machining can also cause interference, no release and slipping problems. Pairing your LuK RepSet with a new LuK flywheel is a smart, cost-effective alternative to resurfacing.
LuK® is a leading manufacturer of the systems and components for vehicle's powertrains. It was the first company in Europe which engineered the diaphragm spring clutch with a release system which is now installed in every third new car. At present the company manufactures dampers, components for clutch systems, transmissions, as well as products for tractors. The newest innovative product developments of LuK are the automation of manual transmissions, torque converters, and components for CVT transmissions that could handle more than 300 Nm of torque.