Name: Fabspeed® - DME™ Software Upgrade Chip
Brand: Fabspeed
SKU: mpn4693033524
Price: 821.22 USD
Availability: OutOfStock

Vehicle Fitment

Make	Model	Year
Porsche	911 Series	1984-1989

Product Details

DME™ Software Upgrade Chip by Fabspeed®. Performance DME chip upgrade improves horsepower, torque, and driving characteristics by reprogramming various sensor inputs, air/fuel ratios, and boost pressure (if applicable).

Specifications

Max Horse Power Gain: 15 HP

Max Torque Gain: 10 lbs. x ft.

Features

Designed for enhanced engine performance
Offers excellent fuel economy
Made to stringent quality standards
Built to provide years of flawless service

Not just another one size fits all' performance chip. Hundreds of hours of code revisions and road and dyno testing on over a hundred Carrera 3.2s have unleashed new pockets of performance previously undiscovered - performance unavailable from anywhere else. No one else has even come close to the amount of research performed on chipping the 3.2 engine. Guaranteed to outperform, all chips have a 100% satisfaction guarantee. With a wide matrix of chip programs available to suit a variety of engine performance modifications and owner preferences, the most popular are listed below. This insures the optimum setup for each particular car.

Programs are available for both the catalyst spec U.S. motors, and the Euro/ROW spec cars. All programming for US version cars by default is for 91 or higher octane fuel. If programming for 93 octane fuel is preferred, please note your octane preferences. For Euro/ROW spec cars, default chip programming is for 95 RON octane fuel. If programming for 98 RON fuel is preferred, please note your octane preference.

The following runs are from an '87 Carrera 3.2 performed on a Dynojet 248c. The motor is a completely stock U.S. spec 3.2 with the exception of a euro premufflerr. The red curves are the car initially dynoed on the stock chip, showing a maximum of 188.6 SAE rear wheel hp (rwhp) at 6000 rpm and 174.9 ft-lbs torque. Calculating for a 15% transmission loss (rwhp/0.85) the motor produces 221.8 HP at the engine. Subtracting for the approximate 6-7 hp gain of the premuffler, that comes close to the factory 214 SAE (217 DIN) hp rating of the car.

With the retuned performance chip for 91 octane pump gas and the premuffler, the motor now exhibits a much more power optimal air/fuel ratio, and redynos a maximum of 206.3 rwhp at 6200 rpm and 184.0 fb-lbs of torque, as shown in the blue curves. At 6200 rpm, compared to the 182 hp the stock chip makes, that is a 24 rwhp gain (29 hp gain at the engine). Calculating for a 15% transmission loss, the engine with the chip produces approximately 243 HP at the flywheel.

For over 20 years, Fabspeed® has been engineering and manufacturing the world's finest stainless steel high-performance exhaust systems and components, air intake products, ECU tuning, and more, specifically-tailored for high-end sports cars and exotics. From Porsche to McLaren, the Fabspeed expertise is unmatched and it shows in everything that the manufacturer creates. Their dyno-proven performance products provide an exhilarating driving experience and are backed by a limited lifetime warranty. Being dedicated to providing maximum performance and true care and concern for the development of their products, Fabspeed strives to be a force of innovation within the industry.

Brand:

Fabspeed

Part Number:

FS.POR.911.DME

Alternate MPN:

FSPOR911DME

Warranty

Limited Lifetime Warranty & Conditions

Fabspeed Motorsport USA™ products (excluding catalytic converters) are backed by a Limited Lifetime Warranty against defects in materials and workmanship which is extended to the original purchaser of the product(s). The catalytic converters used in Fabspeed Motorsport products are covered under warranty for 24 months from the date of purchase. Any catalytic converter issue(s) experienced outside of the established 24-month timeframe is the responsibility of the original purchaser.

Disclaimer: There is no warranty of sound quality or volume, as these are completely subjective characteristics.

Upon verification of warranty coverage, Fabspeed® will, at its sole option, repair or replace the defective product without charge. This is the only remedy the Consumer has for any loss or damage, however arising, due to nonconformity in or defect of the product.

Fabspeed Motorsport reserves the right to deny warrant service if it can be proved that the product failed or is failing due to accidental damage, external impact, abuse or misuse, track/race use, shipment, handling, storage, worn or faulty engine mounts and/or exhaust mounts, faulty location or installation, excessive vibration, internal explosion or backfire, maintenance in a manner not conforming to the Fabspeed® instructions, failure of a third party component, or the installation of the part(s) to a vehicle for which it was not intended.
Exhaust mounts and engine mounts must be checked at least every 12 months by a qualified technician and replaced as necessary. Valid evidence of this regular service may be required in the case of a claim. Fabspeed reserves the right to deny warranty replacement or repair if it is proved that a faulty engine or exhaust mount was responsible for the issue in-question. Attempted repair of a faulty Fabspeed product by anyone other than Fabspeed Motorsport or a Fabspeed-approved agent will void this warranty. .

Fabspeed offers a limited lifetime warranty on all of their performance products*. This warranty is offered to the original purchaser and protects against defects in materials and construction.

*Exclusions:
Catalytic converters: 2-year limited warranty (details below);
Exhaust tip finish: 1-year limited warranty;
Exhaust valves & (related electronics): 1-year limited warranty;

Fabspeed Motorsport Catalytic Converter Warranty:
Fabspeed products containing catalytic converters are protected by a 2-Year limited warranty against failure or defects in material and construction. This warranty does not apply if the product(s) has been installed on a vehicle that has been run with leaded race fuel or fuel additives.

In order for Fabspeed to replace a catalytic converter under the warranty, the following conditions and requirements must ALL be met:
1. Catalysts must not show any physical damage or signs of abuse. Signs of abuse include, but are not limited to, motorsport or on-track use, leaded fuel, fuel additives, etc.
2. Catalysts must be no more than two years in age from the original purchase date.
3. There are no visible exhaust leaks anywhere in the exhaust system upstream of the catalysts.
4. Two ECU printouts showing catalyst inefficiency faults. After the first printout the ECU fault memory is cleared. If the fault returns, a second printout should be made and submitted for warranty approval. Printouts must include operating conditions and vehicle hours.
5. No other faults which will alter the OEM or Fabspeed ECU tune air/fuel calibration should be present on the printouts for catalytic inefficiency (for example: codes for fuel trim, O2 sensors, MAF sensor, etc.)
6. A graph of the oxygen sensors before and after the catalyst must be supplied. This graph should show the oxygen sensors in operation on a fully warm vehicle in closed loop operation.

Magnuson-Moss Warranty Act:

Legally, a vehicle manufacturer cannot void the warranty on a vehicle due to an aftermarket part unless they can prove that the aftermarket part caused or contributed to the failure in the vehicle (per the Magnuson Moss Warranty Act (15 U.S.C. 2302(C)) Learn More

Reviews

(0)

Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.

Fabspeed® - DME™ Software Upgrade Chip

Questions and Answers

(0)

If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!