Name: BREMI® 30114 - Mass Air Flow Sensor
Brand: Bremi
SKU: mpn2620411733
Price: 107.30 USD
Availability: InStock

Vehicle Fitment

Make	Model	Year
Mercedes	C Class	2006-2012
	CL Class	2007-2010
	CLK Class	2006-2009
	CLS Class	2007-2011
	E Class	2006-2011
	G Class	2009-2014
	GL Class	2007-2012
	GLK Class	2010-2012
	M Class	2006-2011
	R Class	2006-2011
	S Class	2007-2013
	SL Class	2007-2009, 2011-2012
	SLK Class	2005-2011

Product Details

Mass Air Flow Sensor by BREMI®. Bremi has been an original equipment manufacturer and aftermarket supplier of Ignition products for Generations. Bremi’s strength lie in their ability to consistently provide industry leadership with innovative technology. Their Air Mass Sensors are manufactured under the same standards (ISO/TS16949) & continually optimized for fast response times resulting in a durable, high performance product that you can rely on!

Features

Perfect solution to keep your air intake system performing the way it was designed to
Crafted from the highest grade materials for dependable, long-lasting service
Engineered using the latest technology to provide outstanding performance
Meticulously tested to be free of manufacturing defects in materials and craftsmanship
Made to fit your specific vehicle perfectly for fast, modification-free installation

BREMI® is an industry leader in the field of original and aftermarket ignition equipment for the automotive industry. Being the part of the Aichele Group, BREMI designs and manufactures ignition systems and components for high-performance vehicles as well as classic cars. BREMI is a major supplier of original ignition parts for such automotive industry giants like BMW and Volkswagen. Ranging from distributor caps and rotors to ignition coils and wires, BREMI products meet strict industry standards and requirements.

Brand:

Bremi

Part Number:

30114

Alternate MPN:

30114

OE Numbers:

273-094-09-48

Warranty

BREMI distributes high quality COP components. BREMI utilize independent engineers to monitor their coils and test warranties. Most coils that are returned do not have a problem. Rough running engines that set misfire codes can have multiple causes. It is the responsibility of the dealer/installer of their products to verify that the following items of inspection have been performed, in order to comply with warranty replacement. General misfire codes are most likely due to an intake vacuum leak or fuel delivery problem. Misfire codes identifying a particular cylinder are usually due to a fouled spark plug, dirty or dead fuel injector or loss of compression in the cylinder burned or bent valve, weak or broken valve spring or leaky head gasket. If the crankshaft position sensor fails, the loss of the basic timing signal will prevent the system from generating a spark and the engine will not start or run. A failed driver circuit within the power train control module (PCM) can kill an individual coil and prevent that cylinder from firing. Replacing the coil without addressing the cause will only result in another damaged coil. Misfire codes can also be triggered from a damaged wire harness due to poor grounds. Inspect the wire harness carefully. You may have to cut back the insulation to verify that there is no corrosion or melting of the wire harness due to poor grounds. A faulty harness can cause the coil to fail. If you simply install a new COP it may seem like you have corrected the problem but, merely replacing the coil without repairing the grounding problem may result in future coil failures. In summary, it is important to remember that ignition misfire can also be caused by other factors such as worn or fouled spark plugs, loose or damaged coil connectors or terminals, dirty fuel injectors, low fuel pressure, intake vacuum leaks, loss of compression in a cylinder, even a tankfull of "bad" gas contaminated with water. These other possibilities should all be ruled out before a COP unit is replaced. Note: A fouled spark plug can damage the COP. BREMI recommend that you always replace the spark plugs when you replace the COP units and that all the ignition coils be replaced at the same time. As a form of preventive maintenance we suggest this be done every 60,000 miles BREMI will do their job to monitor and test the integrity of their coils. BREMI hope that this information will help you to enhance the reliability and credibility of your repair while complementing their product. The main goal here is a real solution to your ignition problem which will result in happy customers. Temporary solutions will only result in the return of non-defective parts and unhappy customers who will continue to have the same problem.

Magnuson-Moss Warranty Act:

Legally, a vehicle manufacturer cannot void the warranty on a vehicle due to an aftermarket part unless they can prove that the aftermarket part caused or contributed to the failure in the vehicle (per the Magnuson Moss Warranty Act (15 U.S.C. 2302(C)) Learn More

Reviews

(0)

Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.

BREMI® 30114 - Mass Air Flow Sensor

Questions and Answers

(0)

If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!