SS4 Plus Deep Stage Drilled and Slotted Front Brake System (4301451FR) by Baer®. Quantity: 1 Pair. The SS4 Plus Deep Stage Drag Spec front brake set is designed as a bolt-on replacement kit for vehicles originally equipped with disc brakes. SS4+ provides racetrack levels of grip for heavier vehicles up to 3,200 pounds competing in drag race conditions. Smaller two-piece 11-inch rotors allow the use of OEM 15-inch front wheels, and 4-piston aluminum calipers equipped with ceramic brake pads provide the grip to slow to a stop in less distance from triple-digit speeds. Calipers feature a protective layer of powder coating to resist scratches and grime.
Notes
Wheel template is required to be used before ordering.
Available as bolt-on replacement kit for disc brake vehicles, or in drum brake conversion kit form
Specifically designed for vehicles up to 3,200 pounds
SS4 Plus Deep Stage Drag kit comes with 11-inch rotors that are slotted and drilled for better venting of heat, water, brake dust, and gasses
SS4 Plus calipers feature 4 pistons each for excellent braking performance
SS4 Plus rotors feature a two-piece design with aluminum center that offers the performance benefit of less rotational mass
SS4 Plus rotors reduce heat buildup with cooling vanes that are unidirectional for each side of the vehicle to increase airflow through the center of the rotors
Stainless steel pistons and hardware offer a high level of resistance to heat transference to the brake fluid
Extended-length caliper pistons will not fall out or become damaged even when brake pads are removed or worn to minimum thickness
Calipers retract deeper to minimize drag with the use of square shoulder seals in place of O-rings and residual valves
SS4 Plus pads are installed from the bottom of the caliper to prevent flying out of the top should extreme conditions cause separation
Stainless steel caliper brackets are designed to accept a second caliper set for later upgrades to match the SS4+ Dual Stage design
SS4 Plus calipers are designed and built specifically to match individual rotor thicknesses, so no adjustment spacers are needed
SS4 Plus kits designed for vehicles with hubs feature billet dust caps and ARP 1/2 x 20 3" race studs
1-piece caliper housings feature a durable clear powder coat finish that is resistant to chips, grime, and brake dust
Calipers come pre-loaded with ceramic brake pad that offer superior heat disbursement, longer life, quieter operation, and lower dust levels
Rotors are dipped in zinc to resist corrosion on non-contact areas
90 days Warranty against Manufacturer's defects
Proudly manufactured in the United States
Benefits:
Drilled Holes and Slots create an escape route for debris, dust, gases, and water
Slots help to increase pad bite and improve air circulation
Slots clean and de-glaze pad surface for optimum pad coefficient of friction
Drilled rotors improve the appearance of your wheels and provide reduced rotor weight
2-Piece rotors offer great weight savings and provide rapid heat dissipation compared to 1-piece rotors
Vented type of rotors offer much faster heat dissipation
Multi-piston calipers provide clamping force on both sides of the rotor at the same time and uniformly transfer braking force to the brake pads
Caliper pistons are hollow to save weight
Aluminum caliper body allows for exceptional light weight (up to 40% of weight savings) and ensures superior corrosion resistance
Caliper heat-resistant coating prevent cracking and fading
Fixed calipers create friction from the brake pads on both sides of the rotor at minimum time interval
Baer SS4 Plus Deep Stage Drag Spec brake kits are specifically designed for vehicles over 3,000 pounds to provide strong, confident braking at triple-digit speeds when the quarter-mile run is over. Front rotors are 11 inches in diameter to fit OEM size 15-inch wheels. While they are the smallest brake rotors Baer offers, they measure up to the best in their ability to resist heat buildup and maintain uncompromised braking. Cooling vanes in the center of SS4 Plus rotors are unidirectional for each side of the vehicle to increase airflow, pads retract deeper into the calipers to minimize drag with the use of square shoulder seals, ceramic brake pad construction stays cooler, and stainless steel componentry resists the heat transference to brake fluid that causes fade under hard conditions. SS4 Plus Drag Spec rotors have a two-piece design with center sections crafted from aluminum - removing 3 pounds of rotational mass from the center to quicken brake response. Rotor surfaces are cross-drilled and grooved for superior disbursement of heat, brake friction gases, dust, and water.
At the heart of the SS4 Plus Drag Spec brake kit are the 4-piston calipers themselves. Relentlessly engineered to deliver under high stress conditions, the one-piece aluminum housings are sized to work with each rotor thickness - without using makeshift spacers between caliper halves the way some products from competitors do. Pistons have a longer length, which prevents them from falling out or becoming damaged when brake pads reach zero thickness. SS4 Plus Drag Spec calipers also retract the brake pads deeper to minimize drag by using square shoulder seals, not O-rings and residual valves which take up space. And the calipers are designed so that pads are installed from the bottom instead of the top. So in the unlikely event brake pad components separate under extreme conditions, they will exit to the ground instead of flying up into wheel wells and ricocheting into brake lines.
Stainless steel caliper brackets protect the aluminum caliper assemblies from wear, and feature 2 positions to allow the addition of a second set of calipers later. Calipers come pre-loaded with ceramic brake pads that offer superior heat disbursement, longer life, quieter operation, and lower dust levels, and a durable powder coat finish protects them from rock hits and corrosive grime. We invite you contact our knowledgeable specialists seven days a week for help with any questions you have on Baer brake kits at 800-505-3274.
Founded in 1986 in Phoenix, Arizona, Baer® began with the goal of producing only superior brake components and kits for the driver who appreciates high levels of performance on the street and on the track. Company leaders have always been relentless in their pursuit of making better products through innovation and quality control measures that result in defect-free manufacturing. Whether you're looking to upgrade factory brakes with OEM size components, larger calipers and rotors, or convert a classic with drum brakes to discs, Baer offers a wide selection of brake packages for every driving purpose and budget.
Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.
Baer® 4301451FR - SS4 Plus Deep Stage Drilled and Slotted Front Brake System
/0
Questions and Answers
(0)
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!