Sound Storm Lab® CG30001D - Charge Series 3000W Mono Class D Amplifier

0 reviews|Item # mpn4716874831|Similar Products
$155.41
In Stock (11) - Ships in 24 to 48 hrs
Universal Fit
  • Not Vehicle Specific
Authorized Dealer
Have a Question? Ask a Specialist
888.584.4732Live Chat

Vehicle Fitment

This part is universal

Product Details

Charge Series 3000W Mono Class D Amplifier by Sound Storm Lab®. Get lots of rich, deep, vibrating bass and power for your sound system with this high-tech amplifier from Sound Storm Lab. Incorporating the latest technology, this efficient amp features a MOSFET power supply and variable subsonic filters to provide high power with cut down distortion. This powerhouse provides a crisp, clear sound that conveys every detail of your favorite tunes.

Specifications

Channel Configuration: 1 Channel
Power Supply Type: MOSFET Power Supply
Amp Topology: Monoblock, Class D
Total Power Output: 3000W
Peak Power @ 1 Ohm: 3000W x 1
Peak Power @ 2 Ohm: 1500W x 1
RMS Power @ 4 Ohm: 563W x 1
Strapped Power bridged @ 2 Ohm: 6000W
Speaker Impedance: 1 to 8 Ohm
T.H.D. (Total Harmonic Distortion): 0.01 %
S/N Ratio (A-Weighted): 100 dB
Frequency Response: 15 Hz to 250 Hz ±1 dB
RCA Inputs: 2 Channel
Pre Amp Outputs: 2 Channel
Low Pass Filter: 50 Hz to 250 Hz
Subsonic Filter: 15 Hz to 40 Hz
Bass Boost: Variable 0 to 18 dB
Phase Control: 0 to 180°
Subwoofer Level Control: Yes
Input Sensitivity Switch: Yes
Strappable: Yes
Thermal/Overload/Short Protection: Yes
Dimensions: 13.7" L x 6.5" W x 2.5" H

Features

  • 1 Ohm Stable - The lowest impedance accepted by this amplifier is 1 Ohm. Amplifiers that are 1 Ohm stable produce the most power possible from the amp. An amplifier capable of delivering power at a 1 Ohm load is usually reserved for serious subwoofers that can handle the power
  • Class D Amps - Class D is a high speed switching amplifier technology that is more efficient, generates less heat and draws less power than traditional Class A/B amps. Sound Storm Lab™ use Class D in Sound Storm Lab™ monoblock amplifiers to give you massive amounts of power in a relatively small footprint for clean, powerful, bass
  • Phase Control - The phase control feature allows you to adjust the speakers phase to ensure all audio signals are playing together rather than against each other. When bass notes are noticeably absent, a quick and easy adjustment to the phase control could provide the perfect remedy
  • Protection - If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself
  • Strapping Capability - Strapping capability means that two amplifiers can be linked together to create double the power at an impedance of 2 Ohm. A benefit of strapping is less electrical current is required than if you ran [2] individual amps at 1 Ohm and you only need 1 pair of preamp outputs and RCA cable to connect
  • Subsonic Filter - A subsonic filter is designed for use on subwoofers. Since not all subwoofers can reproduce the same low frequencies, the subsonic filter can be set for optimum bass response in order to keep the driver playing efficiently
  • Subwoofer Level Control - The ability to boost or attenuate the sub level when an amp and subwoofer are connected to the subwoofer pre-amp output
  • Switchable Input Sensitivity - Switchable Input Sensitivity gives you the freedom to connect the amp to any standard source unit and have peace of mind it will be within range to properly match the output of the source unit allowing you to use the volume controls on your source unit the way it was designed
  • Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
  • Variable Gain Control - Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. To much gain will lead to distortion and to little will lead to clipping
  • Variable Low Pass Filter - Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Sound Storm Laboratories® is a multi-million dollar full-line car audio manufacturer. Headquartered in Southern California (about 50 miles northwest of Los Angeles), the company was established in 1997 by a group of car audio professionals whose goal was to bring exciting product designs to the mobile electronics market at affordable prices. This 'more-bang-for-the-buck' philosophy was incorporated into every aspect of the company. MOSFET power supplies, vacuum fluorescent displays, and neodymium magnet structures are some examples of leading edge technologies utilized by Sound Storm Laboratories engineers. Their designers continually research and develop the latest electronics, materials, and production techniques to set the pace for performance, quality, and style in the car audio industry.

Part Number:
CG30001D
UPC:
791489127806

Reviews

(0)
Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.
Sound Storm Lab® CG30001D - Charge Series 3000W Mono Class D Amplifier
/0

Questions and Answers

(0)
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!
CARiD FacebookCARiD TwitterCARiD YouTube ChannelCARiD PinterestCARiD Instagram
Inspiration Gallery
All manufacturer names, symbols, and descriptions, used in our images and text are used solely for identification purposes only. It is neither inferred nor implied that any item sold by CARiD.com is a product authorized by or in any way connected with any vehicle manufacturers displayed on this page.
CUSTOMER SERVICE
INFORMATION
CONTACTS