Duraflex® 106444 - B-2 Style Fiberglass Front Bumper Cover (Unpainted)

I ordered the B-2 Style Front Bumper and the side skirts together for my 2007 Toyota Prius. Everything arrived shipped in the same box, reasonably wrapped, but not very well padded, per se. I had to meet the delivery driver because there was no place for the driver to turn around where I live, so I wasn't able to inspect the contents until I got home with them. There was a small crack in the fiberglass just under the driver's headlight area, about 1/4", which happened during shipping, but otherwise, the bumper arrived in pretty good shape. Removing the old bumper assembly took about 1.5 hours and wasn't bad at all. The two hood rest bolts (they have a rubber ring on them for the hood to rest on while closed) were the hardest to remove. There are a total of about 15 bolts overall, most of them at the bottom end of the bumper, that need to be removed before the bumper will come off. The picture with the product shows driving lights in the 3" holes in the bumper, but be aware that you'll have to fashion retainers for them if you're going to mount driving lights in them. There are *no* provisions for them out of the box, and you can't move the mounts from the old bumper, as they are molded into the assembly. If your old bumper is wrecked, or you have the opportunity to cut them out of a bumper from somewhere, they will fit over the ones in the replacement. I ended up using resin to create the assemblies to hold the driving lights in place. This required 24 hours to allow the assemblies to dry before I could actually install the new bumper. Installation of the new bumper took me about 2.5 hours. Most of this was fabrication and drilling. While the bumper itself is fairly sturdy and shaped well, it isn't an exact fit. There are no provisions for factory mounting bolts anywhere on the new bumper. I would recommend putting in the 5 mounting bolts at the top of the bumper first to keep it stable while drilling the rest to keep it from shifting while doing the remount. The lip under the driver's headlight is tight - very tight. I had to loosen up the headlight and shift it "up" to accommodate it, but there are only two bolts on the headlight assembly to loosen (10mm) and adjust it. There are two things to really watch for when bolting the bumper to the front fenders: - The edges don't run flat with the fenders; there is almost 1/4" difference between the fenders and the bumper (thicker), where they protrude. In essence, it looks like I have a Bra on right now. I'm not sure if I will be able to shave the bumper down so that it meshes flush with the fenders or not. - The curvature of the bumper does not match that of the body, so it sticks out further than the fender. You have to "push" it back in, hold it in place, and then drill your mounting holes while it's being held into place. The lip on the bumper makes it difficult to get bolts into place or to even drill the pilot holes. I didn't reuse the factory valance on the new bumper, which saved me 6 mounting points needing to be redrilled. I would recommend removing the factory gravel shield, as it is about 2" short of actually reaching the new bumper to be redrilled and mounted. I ended up using a box cutter to cut the shield off at the crossmember. Overall, it's a really nice bumper; it might seem like I'm beating them up on the review, but I'm not. Understand that if you purchase anything like this for your car, there are going to be modifications needed; it's not likely that you'll just be able to pull it out of the box, put it on, and have everything be 100% perfect. There are things about this particular kit that could use some improvement - I'm just trying to point out the obvious issues that I ran into with it. Overall, I think the bumper looks fantastic on the car, but not without some effort on my part to make everything look good. If you don't mind the fabrication required to make everything right, I think you'll be pleased with it.

The build quality was nice, love how clean it came but the rear bumper had a small crack on it but I’m not complaining about it. This kit was well delivered and somewhat cared for *back bumper small crack*. Everything was in one box, I was told I would possibly come separate but since it was ONE whole item it came in one whole box. Haven’t put it on my Camry yet but a test look had me satisfied.

I destroyed my stock bumper bc of a dog had to replace radiator the fan belt all that and needed a new bumper bc it destroyed the whole bottom end so glad I got this bumper and the lip oh it’s gonna look good my cars black so I’m in tears staring at it

A cool looking bumper but there were some issues. It is definitely not plug and play. I took it to a body shop it get it fitted into my genesis. The dimensions were a bit off, so there's that. One side fitted perfectly and the other has a gap where I'll have to get filled. Will not be able to use the factory fog lights with these, I replaced mine with 3in halo fog lights. Overall good bumper, only downside is that you need to bring it to a shop to get it fitted professionally.

Bout it, first off bumper was all warped and when I managed to fit it up I had to cut some edges of the bumper to make the bumper fit. Not even a week after installation the whole bumper started to crack, not very rigid whatsoever, flimsily as can be. There are no brackets for the turn signals, had to mold something onto it to get them to fit. Don’t waste your money on this and save up a little more to buy a different hood.

I highly highly recommend not to buy this front bumper and the skirts... It looked good to go if u don't do body work for a living.. Mine would have had to be cut apart and added 2 inches in the middle an widen where it meets up at the wheel wells an once it is on it will not come off to even change ur headlight on the passenger side!!!!! Totally a big upset and it's not even damaged or anything since I got it but I cannot send it back..... Totally bullspit!!!!

Don’t expect this to fit the way you want it too. Took me and my buddy four hours of sanding, and 3 hours it install time. This is a really bad mold. And it’s plexiglass at that. I have about a 1/4 inch headlight gap under the passenger headlight. The driver side was fine.

Being that this bumper is aftermarket I did not expect OEM fitment, I did however expect the cover to at least fit over the metal bumper. That had to have its bracket shaved down. The area around the headlights is just so poorly fitting that there is about 2-3 inch gap all around the headlights. The bumper arrived with hair and dust in the primer and huge globs of body filler that had to be sanded for hours. If you are looking to replace your stock bumper, please buy an actual OEM one. This fit is just so poor and the oem is only 100 or so dollars more.

Best bumper out there, hands down makes car look aggressive.

Doesn't fit with stock bumper. Modification required. Looks good and fits well on wheels and hood when installed. Works well with turbo setups.