Possibly. If it is the same make and model no problem. If you have changed vehicles, the frame size may be too big or too small. Most important is that the mounting hardware is correct for your new truck. This consists of the brackets that attach to the frame, and the vehicle specific stake pocket bolts that mount into your front stake pockets. These parts are available in a package called a mounting kit. Mounting kits are available for purchase. If the frame you currently have is too big for your new truck, you will likely need to drill a few new holes to position the brackets in the correct location. If the frame is too small, you're going to need a new one. Obviously a frame that is too large or small will negatively affect the look of your truck.
On the majority of trucks no. If your truck is a late model fullsize, certainly not. Trucks that do not have stake pockets generally require drilling through the bed rail.
Most people find installing a BackRack simple. As most applications are no-drill, all that is required are a few wrenches. If you have a bedliner or toolbox, the installation is slightly more involved but still easy. If you have a drill application or have multiple accessories like a tonneau cover, the experience of a professional installer is recommended.
Sorry. No Chrome.
Henry Ford had it right... Black only.
Yes, but only tonneaus that clamp to the inside rail of the truck bed are compatible.
Easily. Under the rail liners are the easiest. Simply remove the liner, install the stake pocket bolts (SPB), then reinstall the liner and attach your BackRack. With an over-the-rail liner the procedure is the same, however, you may need to drill holes through the top rail of the liner for the SPBs to protrude through. It is best to place rail plates under the liner on over-the-rail liners.
Yes. The toolbox bracket mounting system allows you to install a toolbox without drilling holes in your truck. Your toolbox sits on top of two channels allowing you to mount the toolbox up against the BackRack frame. This leaves a minimal gap between the toolbox and the BackRack. Without the toolbox brackets, a gap of eight to fourteen inches will exist between the toolbox and the BackRack. The toolbox is fastened to the toolbox brackets as opposed to being drilled or fastened to your truck bed. This means no holes drilled in your truck to fasten the toolbox.
Yes. If purchasing the toolbox brackets separately you will replace the railmount brackets and rail plates that came with the BackRack when you purchased it.
21 inches. This is the length of the channel that the toolbox sits on.
Yes. 31 inch toolbox brackets are available for all trucks excluding Compacts.
Toolbox brackets that are sold separately are meant to replace the existing mounting brackets and rail plates that came with the BackRack. Along with the existing brackets comes a hardware bag containing all fasteners. You use the fasteners in the original hardware bag to install the toolbox brackets. Basically, you are removing the railmount brackets and rail plates and replacing them with the toolbox brackets.
No. The toolbox brackets are designed to sit directly on the bed rails.
You need to establish where on the BackRack you want to locate the light (drivers side, passenger side or center ) and determine what size the light is (diameter or length and width). Click the Accessories Tab to scroll through the available options to find the accessory most suited for your application.
Basically, all late model Fullsize Trucks have TCAs available.
Yes. BackRack do offer Part # 92001 that is a universal TCA for older trucks. This lifts the BackRack assembly 2" as opposed to 1". Sure 1" risers are better but the 92001 will solve the issue for older trucks.
Only tonneaus that fasten to the inside lip of the truck bed are compatible. BackRack requires the top rail of the pickup bed to install. Tonneaus that sit primarily on the top rail of the truck bed are incompatible. Older type button tonneaus and aluminum frame types aren't compatible.
Obviously, it's better to have a tonneau that is listed as compatible on the Tonneau Cover Compatibility Chart.
You need the TCAs to lift the BackRack assembly up 1" to clear the height of the tonneau. The TCAs provide a stable and safe base on which the BackRack can sit. Secondly, the added 1" of height requires an extended stake pocket bolt to replace the original SPB that came with your BackRack.