Product Details
Charge Series 1200W 2-Channel Class AB Amplifier by Sound Storm Lab®. Get lots of rich, deep, vibrating bass and power for your sound system with this high-tech amplifier from Sound Storm Lab. Incorporating the latest technology, this efficient amp features a MOSFET power supply and variable subsonic filters to provide high power with cut down distortion. This powerhouse provides a crisp, clear sound that conveys every detail of your favorite tunes.
Specifications
| Channel Configuration: 2/1 Channel |
| Power Supply Type: MOSFET Power Supply |
| Amp Topology: Full Range, Class A/B |
| Total Power Output: 1200W |
| Peak Power @ 2 Ohm: 600W x 2 |
| Bridged Power @ 4 Ohm: 1200W x 1 |
| RMS Power @ 4 Ohm: 225W x 2 |
| Speaker Impedance: 2 to 8 Ohm |
| T.H.D. (Total Harmonic Distortion): 0.01 % |
| Channel Separation ≥: 90 dB |
| S/N Ratio (A-Weighted): 105 dB |
| Frequency Response: 9 Hz to 50 kHz ±1 dB |
| RCA Inputs: 2 Channel |
| High Level Inputs: Yes |
| Low Pass Filter: 50 Hz to 250 Hz |
| High-Pass Filter: Fixed 80 Hz Hz |
| Bass Boost: Variable 0 to 18 dB |
| Subwoofer Level Control: Yes |
| Input Sensitivity Switch: Yes |
| Thermal/Overload/Short Protection: Yes |
| Dimensions: 11.72" L x 6.5" W x 2.5" H |
Features
- 2 Ohm Stable - The lowest impedance accepted by this amplifier is 2 Ohm. Amplifiers that are 2 Ohm stable produce more power resulting in more volume. This amp can comfortably power speakers or subwoofers with all channel(s) being used at a load of 2 Ohm
- Bridgeable - Bridging an amplifier means to combine channels of a multi-channel amplifier to get more power or flexibility out of it. For instance, on a 4 channel amp, channels 1 and 2 could be used normally for your speakers, and channels 3 and 4 can be bridged for more power to a single subwoofer. A 2 channel amp can also be bridged to power a single subwoofer
- Class A/B - Class A/B amplifiers have long been known for their ability to produce great quality sound while performing more efficiently than pure Class A amplifiers. Sound Storm Lab™ have developed a specific linear circuitry that further reduces distortion while increasing both sound quality and power output
- Fixed High Pass Filter - Fixed High-pass filter gives you the ability to filter the frequencies that pass through to the full range speakers from a fixed frequency point
- High and Low Level Inputs - An amplifier with both high-level and low-level inputs provides flexibility by allowing you to build an audio system using virtually any standard factory or aftermarket source unit. High-level (speaker level) inputs accept the signal from the speakers, while low-level (RCA) inputs accept the signal from the pre-amp outputs of the source unit
- MOSFET - MOSFET stands for Metal Oxide Semiconductor Field-Effect Transistor. MOSFETs are used either as a switch or to amplify a signal. MOSFETs are superior to other FETs, because they require less current to operate, which makes them better suited for car audio
- Protection - If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself
- Subwoofer Level Control - The ability to boost or attenuate the sub level when an amp and subwoofer are connected to the subwoofer pre-amp output
- Switchable Input Sensitivity - Switchable Input Sensitivity gives you the freedom to connect the amp to any standard source unit and have peace of mind it will be within range to properly match the output of the source unit allowing you to use the volume controls on your source unit the way it was designed
- Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
- Variable Gain Control - Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. To much gain will lead to distortion and to little will lead to clipping
- Variable Low Pass Filter - Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.
Sound Storm Laboratories® is a multi-million dollar full-line car audio manufacturer. Headquartered in Southern California (about 50 miles northwest of Los Angeles), the company was established in 1997 by a group of car audio professionals whose goal was to bring exciting product designs to the mobile electronics market at affordable prices. This 'more-bang-for-the-buck' philosophy was incorporated into every aspect of the company. MOSFET power supplies, vacuum fluorescent displays, and neodymium magnet structures are some examples of leading edge technologies utilized by Sound Storm Laboratories engineers. Their designers continually research and develop the latest electronics, materials, and production techniques to set the pace for performance, quality, and style in the car audio industry.