Power-Plus Series™ Aluminum Chrome Cold Air Intake System (1720) by BBK®. Gain horsepower and get an appearance improvement under the hood just by replacing your factory air intake system. The high-flow air filter and large diameter air intake tube replaces the stock restrictive components, and works with factory and aftermarket tunes, providing increased airflow to your engine, for more power and better performance you can feel, without the need for further modifications. The quick and easy installation can be accomplished with simple hand tools.
|Filter Color: Blue|
|Tube Finish: Chrome|
|System Type: Cold Air Intakes|
|Replacement Filter: 1742|
- Improves airflow to your engine
- Includes a shield that isolates the air filter from engine heat, so it can take in cooler, denser, air
- Custom designed and dyno tested for maximum gains in horsepower and torque
- Includes washable and reusable conical air filter that flows up to 75% better than a factory paper air filter
- Large diameter, smoothly contoured air intake tube with built-in high-flow mass air meter housing
- Includes high quality stainless steel clamps and molded silicon hoses
- Works with factory or aftermarket tunes; requires no other modifications
- Comes complete with everything required for installation, including detailed instructions
- Limited 1-year warranty
- Proudly made in the USA
Your stock factory air intake system is a compromise, with air intake noise reduction, cost and ease of maintenance often taking precedence over airflow, even on performance models. Paper air filters are cheap to manufacture, with very small passages that are good at trapping dirt but also restrict airflow. The factory air box is also often very small, limiting the size of the filter, and the factory air intake tube is often small in diameter, has restrictive baffles and makes awkward bends, none of which is good for optimal airflow.
However, replacing this restrictive system with one that would provide peak airflow for improved performance often required an expensive tuner or the vehicle wouldn't operate properly. The engineers at BBK spent many months developing this system and the result is a Cold Air Intake system that not only outperforms competitors' systems but does so using either the factory or an aftermarket tuner. With this BBK system you'll get noticeable gains in power and performance, without having to make any other vehicle modifications. Every BBK system is custom designed and dyno tested to enable your engine to make the most horsepower and torque possible.
The BBK system includes a high-flow conical air filter, heat shield, and high-flow air intake tube. The conical cotton element air filter has much more surface area for up to 75% greater airflow than a factory paper air filter, without sacrificing any filtration ability. The filter is isolated from engine heat with an integral shield, which allows the filter to take in cooler, denser air. Cooler, denser air contains more oxygen, and more oxygen in your engine's air intake charge means better combustion, resulting in greater engine output. The large diameter and smooth contours of the BBK air intake tube maximizes airflow right to the throttle body. The intake tube includes a built-in high-flow mass air meter housing in the opening.
Best of all you can have this performance improvement quickly and easily. The BBK system is a bolt-on installation that can be accomplished with simple hand tools. It works with factory and aftermarket tunes and no other modifications to your vehicle are required. The system comes with quality hardware like stainless steel clamps, and temperature resistant molded silicon hoses, with detailed instructions that will guide you through the installation.
The BBK Cold Air Intake System is backed by a 1-year limited warranty against defects in materials or workmanship, as long as the product was installed according to BBK guidelines.
BBK Performance® is the No. 1 manufacturer of EFI performance parts and accessories. For over 20 years the company has concentrated its resources on the development and manufacture of performance parts and accessories for late model electronically fuel injected vehicles. These parts include large bore, high-flow mass air meters and throttle bodies, intake manifolds, high-flow fuel rails and high-volume fuel pumps, and cold air intake kits. The company also manufactures an extensive line of high-tech headers and exhaust pipes, and state-of-the-art suspension and steering components. Along with their commitment to EFI, the company is also dedicated to designing and manufacturing the highest quality parts and accessories right here in the USA. To that end, the company operates 2 large design and manufacturing facilities in Temecula, California as well as a large distribution center located in Daytona Beach, Florida.