Ford F-150 3.5L 2011, Magnum Force™ Stage 2 Twin Tube Aluminum Polished Cold Air Intake System by aFe®. The aFe Stage 2 Cold Air Intake System replaces your entire factory air intake system with a large high-flow aFe air filter, open element airbox/heat shield and a smoothly contoured, less restrictive intake tube. This system enables your engine to take in huge quantities of dense, cool, oxygen laden air. The result is better combustion, increased horsepower and torque, and a noticeable gain in performance. CA Prop 65 WARNING - This product contains chemicals known to the State of California to cause cancer, and/or birth defects or other reproductive harm.
Notes: California Proposition 65 Warning.
Fitment notes: This is a CARB compliant part, legal for use on vehicles built to meet CARB standards and/or registered in California and other states which follow CARB standards (CARB EO: D-550-15).
|Series: Magnum Force™|
|Tube Finish: Polished|
|System Type: Cold Air Intakes|
|HP Gain: Up to 25 hp|
|TQ Gain: Up to 30 lbs./ft.|
- Improves airflow to your engine
- Isolates the air filter from engine heat, enabling it to take in cooler, denser air
- Increases horsepower and torque, improves performance
- Designed and tested for each specific application
- Includes a conical high performance aFe air filter
- Includes a precision designed rotomolded plastic intake tube
- Comes complete with everything required for installation, including comprehensive instructions
- Can be installed in 45-90 minutes with simple hand tools; no drilling, cutting or fabrication required
- Limited 2-year warranty
- Proudly made in the USA
The Stage 2 Cold Air Intake System will give you the greatest possible performance gain and the most bang for the buck. It replaces your factory, restrictive air intake system with the massive aFe performance air filter of your choice, a one-piece open element airbox/heat shield that seals against the hood, isolating the filter from engine heat, and a rotomolded plastic intake tube with smooth bends for increased airflow volume. The increased flow of cooler air to your engine will result in noticeable gains in power and performance. Cooler, denser air contains more oxygen, and more oxygen in your engine's air intake charge means better combustion, resulting in greater engine output.
The aFe Pro 5R air filter was designed to provide the maximum airflow possible, to enable your engine to make the most horsepower and torque. But aFe didn't achieve this by ignoring engine protection. The Pro 5R outperforms most other cotton gauze air filters with a 98.6% efficiency rating. The increased airflow and high filtration capability are the result of the Pro 5R's construction. It’s made of 5 layers of progressively finer medical-grade cotton gauze.
The Pro GUARD 7 air filter delivers increased airflow while providing the highest level of filtration efficiency available – 99.7%. The patented 7-layer progressive cotton/synthetic media in the Pro GUARD 7 consists of 5 layers of progressively finer medical grade cotton gauze, combined with 2 layers of non-woven synthetic polyester fabric with random porosity.
Competitors use constant size mesh gauze in their filters, which creates voids/openings that can allow dirt to pass through. As the progressively finer layers of gauze are stacked in the Pro 5R and Pro GUARD 7, the randomness of the openings increase, minimizing spaces with no filter media. Dust accumulates on multiple layers, increasing overall dust holding capacity and filtration efficiency.
The Pro DRY S filter combines high airflow and filtration efficiency with the convenience of oil-free maintenance. It contains 3 layers of randomly porous synthetic fabric, which allows approximately twice the airflow when compared to a typical stock air filter. The increased airflow results in more horsepower and torque, better throttle response and more miles per gallon. But this improved airflow and performance hasn't been gained at the expense of engine protection. The Pro DRY S has an excellent 99.2% filtration efficiency rating.
The pleats in all 3 filters are evenly spaced for greater dust holding capacity and the tips are rounded for better airflow. They're also 30% deeper than comparable aftermarket air filters for longer service intervals and greater dust holding capacity. The sealing surface and supporting structures are made from 100% polyurethane, to withstand extreme engine temperatures.
The one-piece airbox/heat shield is made of rugged 16-gauge powder coated steel. It installs easily in place of the factory airbox; no cutting or drilling is required. The box/shield is attached with quality stainless steel hardware that is supplied with the kit. Top quality, flexible rubber trim at the top of the box/shield seals against the hood when it is closed, shielding the air filter from engine heat and allowing it to take in cooler air. Some systems include a powder coated steel or brushed aluminum cover to further shield the filter.
A specially developed 3-angle velocity stack smoothes the airflow transition from the air filter to the rotomolded intake tube. The precision design and smooth contours of the intake tube maximize airflow volume and speed for optimum power gains.
The aFe Stage 2 Air Intake System comes complete with everything necessary for installation, including comprehensive instructions. It's backed by aFe's limited 2-year warranty and made in the USA.
aFe® (Advanced Flow Engineering, Inc.) manufactures performance products for late model cars, light trucks and SUVs. The company was founded in 1999 with an initial concentration on high performance air filters. Since then, the company product line has broadened to include cold air intakes, fluid filters, exhaust systems, intake manifolds, intercoolers, programmers, differential covers, transmission pans and throttle body spacers. The team of engineers, machinists, production and sales people at aFe® have many years of experience in their respective positions, and together work to ensure they produce the best automotive products on the market.