Toyota Supra 1993-1995, Series 2 Plug and Play Engine Management System by AEM®. Get complete control of your car’s engine and driveline using the vehicle’s factory wiring and sensors with the Series 2 Plug and Play Engine Management System. It plugs right into your car’s factory ECU harness and requires no additional wiring or hardware. The Series 2 EMS contains AEMTuner Windows-compatible software that is infinitely adjustable, allowing you to tune your engine by programming virtually any combination of engine control, power adders, and auxiliary devices, and accurately deliver the proper amounts of fuel and correct ignition timing for any boost level or operating condition. Laptop tunable via USB or serial connection, 6’ serial cable and 10’ USB cable included.
|Quantity: 1 Piece|
- Delivers complete control of your car’s engine and driveline
- Plugs into your car’s factory wiring harness and uses existing sensors
- Runs on Windows compatible software
- Included AEMTuner software simplifies tuning process
- Includes USB and serial port for tuning via laptop or PC with included 10’ USB cable and 6’ serial cable
- Includes start-up calibrations
- Systems are unlocked and fully enabled – never pay for upgrades
- Works with all AEM gauges and communicates with AEMnet enabled electronics
- Internal data logger with 2MB memory
- Logging software for data analysis
- Comes with detailed instructions
- Limited 1-year warranty
AEM makes it easy to hot-rod your modern fuel-injected, computer-controlled car. Instead of installing performance parts like bigger injectors and nitrous oxide and trying to make them work by modifying the harness, sensors, or adding modules, just install AEM’s Series 2 Plug and Play EMS and you’ll have complete control of your engine and driveline. The Series 2 EMS allows you to control every aspect of your engine, including variable valve timing, RPM limit, timing, adding larger injectors, boost control, nitrous injection, even anti-lag and individual cylinder fuel and timing trims. And it does this using your vehicle’s factory wiring harness and existing sensors. The Series 2 EMS is a real plug and play unit; it connects directly into your vehicle’s factory ECU harness and requires no additional wiring or hardware. It comes loaded with AEM’s Windows compatible AEMTuner software, which simplifies copying, viewing, and data manipulation. Just connect your laptop or PC to the Series 2 EMS with the included 10’ USB cable or 6’ serial cable, and start tuning.
The Series 2 EMS can accommodate 3 trigger inputs (Ref/Sync), up to 12 analog voltage inputs, up to 6 analog temperature inputs, up to 8 switch inputs, 2 Lambda inputs, and 2 knock sensor inputs. It has an internal barometric pressure sensor, and a user adjustable knock sensor center frequency. It’s capable of up to 12 injector outputs, up to 8 ignition outputs, up to 12 general purpose low side outputs, up to 4 general purpose high side outputs, and individual cylinder ignition and fuel trims.
Functions and features include groundspeed based boost target, staged nitrous injection, ground speed limiting, overrun boost enhancement (anti-lag), gear change ignition cut (shift without lift), stepper motor idle control, continuously variable cam control for 4 cams, main relay control, VTEC control, fuel and ignition rev limiters, “in-cockpit” global fuel trim capability, and gear dependent shift light.
Start-up calibrations are included to get you headed in the right direction. The AEMTuner software has colored tables and maps, includes a support pane to give you context sensitive help, and uses tuners’ actual calibrations to describe each function. You can graphically compare tables and maps for easy analysis, and internal conflict detection will alert you if obvious errors exist in the assignment of inputs/outputs. The included AEM data analysis software features advanced 3D graphics, and allows you to review and playback vehicle, driver, or engine data and overlay this data using charts, dash displays, gauges, or custom displays that you create. Maps can be password protected to prevent unauthorized usage or sharing.
John Concialdi and Bob Sullivan co founded AEM® in 1987 as a tuning performance shop in Compton California. Both men had extensive technical backgrounds in engines and engine airflow, and in a short time AEM became the go-to company for performance modifications. By 1993, when the company relocated to Gardena California, it had become commonplace to see cars wearing the bright yellow AEM logo winning races. AEM tirelessly dyno tested and worked closely with racers and auto manufacturers in an effort to understand intake energy dynamics. This resulted in the sale of their first air intake kit in 1994. AEM can boast a number of firsts and unique products: They’re the first manufacturer to make an intake system with specific tube lengths and diameters to take advantage of pressure waves in the inlet tract; they developed the first dual chamber intake kit; they designed an air bypass valve to prevent hydro-lock should the air filter ingest water; and they created one of the first hybrid intake systems for modified cars. AEM continues to create innovative products to help you get more power from your car.