It is not recommended to use the ARB Compact Air Compressor (CKSA12) to inflate tires. This compressor was designed only to engage ARB Air Lockers. For tires up to 35” in size, ARB recommend the ARB Medium Compressor (part no. CKMA12) and for tires above 35”, the ARB Twin Motor CKMTA12 compressor (CKMTA12).
For Tire inflation, the vehicle-mounted compressor requires addition ARB Pump Up Kit #171302, which includes 19 feet air hose, quick connector coupling, clip-on tire inflator, and accessories. If using an ARB Twin Compressor (CKMTA12), the addition of a manifold (171503) is required.
ARB provides a 5-year (Air Locker) and 2-year (Compressor) warranty that covers defects against workmanship or materials.
ARB vehicle mount compressors can be installed in various locations on the vehicle, including the engine bay, cabin, rear cargo area, etc.
The ARB Compressor will perform better when it receives 14 volts from the alternator vs the 12.6 volts from the battery alone. Also, the battery will not be depleted by the compressor if the engine is idling.
An ARB Air Locker can be engaged at any speed as long as both wheels are spinning at the same rate. If one wheel is spinning faster than the other, what is called “crash locking” will occur and can cause damage to the internal gears. ARB recommend that the vehicle stops and engages the Air Locker before attempting an obstacle.
Fitment of ARB Air Lockers to vehicles fitted with OE locking differentials varies from vehicle to vehicle.
ARB strongly recommends the use of a genuine ARB Air Compressor; however, the Air locker can operate on any alternative air source that meets the requirements as stated in Air Locker fitting instructions.
No, each of our air compressors has provisions to activate 2 (two) Air Lockers i.e., front and rear.
ARB off a kit (ALAP) that includes everything you need to plum your compressor to the ARB Air Locker.
ARB recommend following your vehicle users manual for the quality and viscosity. ARB DO NOT suggest any oils with limited-slip additives as they can shorten the life of the ARB Air Locker seals.
The ARB Air Locker will engage at around 70 PSI. However, for faster engagement and disengagement, we recommend an air pressure supply between 100 and 150 PSI.
ARB provides a 5-year (Air Locker) and 2-year (Compressor) warranty that covers defects against workmanship or materials.
The number one cause of differential oil traveling up the ARB Air Lines is due to differential housing pressure. If the housing does not vent properly, pressure will push the oil up the lines. To remedy this, check to make sure your factory breathers are not clogged or enlarge breather ports/hoses to allow more ventilation. ARB now offers a breather kit (170112) to help remedy axle ventilation problems.
In select applications, ARB incorporated factory fog light provisions. E.g., JK Wrangler, 200 series VX/Sahara, etc.
ARB does not recommend the modification of any bumper due to the integration with the vehicles air bag system and structural integrity.
All ARB Bumpers come in either a high-quality black powder coat finish that is paintable or ARB’s new textured Integrit powder coat finish.
Factory fog lights incur frequent design changes that result in improper fitment in most ARB Bumper applications. In these cases, either an ARB fog light kit will be supplied or will be an optional accessory with the bumper. In most cases, the factory fog light harness may be used to power the included/optional ARB fog light kit.
Installation times vary from vehicle to vehicle depending on the complexity of the design; however, the average fitting time for an experienced fitter is approximately 6 hours.
ARB Bumpers have been designed with provisions for a wide range of accessories, including spot/flood lights, 12V winches, antennas, and more.
ARB provides a 2-year, 25,000-mile warranty that covers defects against workmanship or materials.
This can vary from vehicle to vehicle depending on the OEM front spring rate and any additional accessories fitted to the vehicle. When a bumper and winch are fitted, upgraded suspension is highly recommended.
Yes, ARB Fridge Freezers have been tested with name brand solar panel systems. Please contact the solar panel system manufacturer for a recommended system.
Amp draw depends on how often the compressor needs to run to maintain the set temperature. This will be determined by the ambient temperature, how often the fridge door is open, and the contents of the fridge. During optimal conditions, the ARB Fridge Freezer will draw under 1.5A to maintain the set temperature.
All ARB Fridge Freezers require a constant supply of 12v, 24v, or 110v to operate.
Most power outlets on newer vehicles do not offer a full 12.6 volt when off due to improper wiring gauge for the application. ARB Fridge Freezers use a low voltage cutoff that prevents the fridge from running if it detects a low voltage. This feature ensures the fridge freezer will prevent your starting battery from going completely flat. If your vehicle wiring is not adequate, ARB offers a stand-alone wiring harness (10900027) that is compatible with all ARB Fridge Freezers.
ARB incorporated factory fog light provisions. E.g., JK Wrangler, 200 series VX/Sahara, etc.
If you would like to run another brand of winch, please compare the overall dimensions of the Warn winch listed with the other brand.
ARB does not recommend the modification of any bumper due to the integration with the vehicles air bag system and structural integrity.
All ARB Bumpers come in either a high-quality black powder coat finish that is paintable or ARB’s new textured Integrit powder coat finish.
Factory fog lights incur frequent design changes that result in improper fitment in most ARB Bumper applications. In these cases, either an ARB fog light kit will be supplied or will be an optional accessory with the bumper. In most cases, the factory fog light harness may be used to power the included/optional ARB fog light kit.
Installation times vary from vehicle to vehicle depending on the complexity of the design; however, the average fitting time for an experienced fitter is approximately 6 hours.
ARB Bumpers have been designed with provisions for a wide range of accessories, including spot/flood lights, 12V winches, antennas, and more.
ARB provides a 2-year, 25,000-mile warranty that covers defects against workmanship or materials.
This can vary from vehicle to vehicle depending on the OEM front spring rate and any additional accessories fitted to the vehicle. When a bumper and winch are fitted, upgraded suspension is highly recommended.
All Old Man Emu springs have been designed and specially tuned to work in conjunction with Old Man Emu shock absorbers for each specific vehicle.
For most applications, ARB offer Old Man Emu springs in Light, Medium or Heavy Load options. The correct application will depend on how your vehicle is equipped with aftermarket accessories that add additional weight to your vehicle. In most cases, you would use a light load spring on a vehicle with no aftermarket bumper and a medium or heavy load spring on a vehicle with an ARB Bumper.
ARB suggest that you set the dampening per the instructions and then move one adjustment at a time using the included tool until you find your preferred ride quality.
Lift height varies from vehicle to vehicle due to the vehicle’s suspension limitations.
In most cases, Old Man Emu suspension systems are designed to maintain the factory front-to-back rake. This is because Old Man Emu suspension is engineered for load-carrying ability as well as lift. In some cases, a rear leaf may be removed from the pack to level the vehicle, but there is a downside, the spring rate is also reduced. The spring will lose more height under when loaded causing the rear to sit lower than the front resulting in poor and sometimes dangerous ride quality.
ARB provides a 3-year, 37,000 mile warranty that covers defects against workmanship or materials.
The majority of ARB Old Man Emu suspension components are designed around factory frame, axle, and control arm mounts and install the same as the factory components.
Specific suspension fitting kits have been developed to ensure that vehicle dynamics have not been altered including but not limited to) driveline, braking, and steering operation.
Old Man Emu suspension systems are engineered first and foremost for ride and handling quality. The amount of lift provided for each specific vehicle is within the maximum limits allowed by the stock suspension components so that extensive and costly modifications are not required.
Installing OME suspension will help handle increased tongue weights, but will not increase your tow rating. Please follow the towing specifications per your owner’s manual.
It is not required to rotate your snorkel intake head around while driving in the rain. The Safari Snorkel head is designed to drain any water that penetrates the intake head automatically.
Although the Safari Snorkel prevents water ingestion into the vehicle’s intake system, the snorkel does not make an engine waterproof. Caution and preparation still must be taken when crossing deep water.
This will vary from model to model as access/drainage provisions have not been integrated into all application.
Most applications have been designed to allow fitment with factory bumper or an ARB bumper.
ARB UVP and recovery points are only manufactured in steel.
ARB does not include brackets with the awnings because every fitment may require a different style of bracket. ARB offers a universal “L” bracket and bracket set to be used with ARB Roof Racks (sold separately).
ARB Roof Top Tents are universal. They can be fitted to any flat surface as long it’s capable of handling 170lbs of dynamic weight.
ARB Awnings are universal. With proper brackets (not included) the awning can be mounted to roof racks, cross bars, and flat surfaces.