Universal Fittings by Air Lift®. Air Lift offers replacement air line fittings identical to original equipment found in all air suspension kits they sell. Here, you’ll find transducers, blowoff valves, air line “t” splitters, check valves, elbows, and a multitude of coupler pieces designed for push-to-connect air lines and for traditional thread applications – in the sizes you need. All components are designed to look good and remain free of corrosion with either brass construction or a nickel plating finish.
- Full selection of replacement transducers, blowoff valves, air line “t” splitters, check valves, elbows, coupler pieces, and more
- Fitting ends are available in a choice of thread pitch configurations
- Push-to-connect components are available for inflation as well as splitting/redirection of air flow
- Fittings feature either brass construction or nickel plate finish for corrosion resistance and show car looks
- Manufactured in the United States
Air Lift builds all replacement fittings, pressure valves, splitters, and more to the highest quality standards to ensure your air suspension system continues to perform the way it was meant to. Most components come in a choice of configurations, making it easy to find the part you need for your exact system by clicking on the “Select Options” bar above. For starters, you’ll find a replacement Pressure Transducer that measures pressure and converts it to an electrical signal. Blowoff valves designed to release excess air pressure when psi exceeds 200 are here, as well as a Check Valve that maintains one-way pressure flow with two identically-sized female ends for same size air line fittings. We also have Drain Cock brass drainage valves which allow water that normally collects in the bottom of your tank to be drained out effectively and easily. If you need to seal up and close off the end of any air line, Pipe Plugs are available with a raised hex head top or with a flush countersunk design.
Whatever fitting you need to screw in place, Air Lift’s Thread Sealant Packet contains non-hardening sealant which creates an instant airtight and watertight seal without causing difficulty loosening fittings. If you need replacement air inflation fittings, the Inflation Valve allows manual filling and release of air spring pressure from any outside pump. The Push to Connect quick-connect inflation valve locks into place after being pushed on to any 1/4-inch air line, and Straight pieces with male and female thread designs are receiver pieces for push-to-connect inflation valves.
You’ll also find all the replacement coupler pieces you need from Air Lift as well. If you need to split air from one to two lines, the Branch Tee fitting has one male input end that splits air pressure in opposite directions to female output connectors. The Bushing fitting allows an air line of one size to be connected in a straight path to an air line of a different size. The Coupling with two female ends connects air lines of equal size together for two-way air flow, and the Nipple coupling connects two male end air line fittings together. Should you need to create a 90 degree bend in your air line, the Elbow fitment piece makes that possible. If you’ve got a male threaded end on one side and a female threaded end on the other, the “Street Tee” fitting piece joins them together. And for push-to-connect fittings, the Union, Union Elbow, and Union Tee coupling pieces all allow easy splitting or redirectioning of air lines. All Air Lift fittings are designed for the long run, and brass construction along with nickel plated finishes ensures they will look good on your show vehicle and remain free of corrosion for as long as you use them.2.14 93.12
Brand: Air Lift Part Numbers:
Founded in 1949 in Lansing, Michigan, Air Lift® pioneered the first rubber air bladder that fit inside coil springs to give pickups and other transport vehicles greater load-leveling and ride-stabilizing abilities. These found wide acceptance on commercial vehicles and were soon adopted throughout NASCAR and other professional stock car racing series after assisting many drivers to achieve victorious finishes. Over the decades, Air Lift® has continued to pioneer innovative developments with air spring helpers and stand-alone air springs for mobile homes, ambulances, and heavy trucks. During the 1990s, the company was on the cutting edge – developing high-performance air springs and complete air suspension systems that allowed extreme lowering, stunts, and higher levels of handling during aggressive driving. Today, Air Lift® is ISO 9001:2008 certified for best business practices, manufacturing, and customer satisfaction and their range of high-quality products is widely respected throughout the industry. CARiD offers the Air Lift® full lineup of full air suspension kits, coil spring helpers, air springs, compressors, air tanks, and more at prices that can’t be beat.Product Reviews (1)
Every Customer can leave a review about our service and the product that was purchased. In order to leave your review for your new product, please follow the link in the email you receive after completing your purchase. You can rate appearance, ease of installation, price/value and product quality.Air Lift® - FittingsAverage Rating: 5 of 5APPEARANCEEASE OF INSTALLATIONPRICE/VALUEQUALITYAll Air Lift Reviews
Product Reviews (1)
Product Reviews (1)